Videos

A new cap kit designed for the FX-600 and FX-601 s...

A new cap kit designed for the FX-600 and FX-601 soldering irons. This protective cap is easy to install and take apart. Once installed, you simply unscrew the cap to expose the soldering iron tip for use. When you are finished soldering, unplug the soldering iron and screw the cap back on. The heat resistant plastic prevents the tip from contacting and melting other tools or power cords in your toolbox when you put it away. It also helps reduce the risk of injury from accidentally touching the soldering iron tip when it is cooling down after use.

The new HAKKO FT-720 Tip Cleaner provides quick an...

The new HAKKO FT-720 Tip Cleaner provides quick and effective cleaning of soldering iron tips with sensor activated counter-rotating brushes, which remove tip oxides, debris, and excess solder without damaging the tip plating. The FT-720 is equipped with long life fluoroplastic brushes that minimize temperature drop of soldering iron. The brushes are easy to remove and replace, with optional resin and metal cleaning brushes available.

Watch and learn about the CHP DPF-300 depaneling t...

Watch and learn about the CHP DPF-300 depaneling table. The DPF-300 is a manual router table for depaneling circuit boards (PCBs) from a panel or multi-block with the quality performance of an expensive automated system but at a much lower cost. The DPF-300 is equipped with an industrial-type electric motor spindle, eliminating the need for compressed air, and the steel guide rails are designed for safety and deliver a precision cut every time. Thanks for watching!

The DPF-300 is a manual router table for depanelin...

The DPF-300 is a manual router table for depaneling circuit boards (PCBs) from a panel or multi-block with the quality performance of an expensive automated system but at a much lower cost. The DPF-300 is equipped with an industrial-type electric motor spindle, eliminating the need for compressed air, and the steel guide rails are designed for safety and deliver a precision cut every time.

Sei and Kai talk about the features of the portabl...

Sei and Kai talk about the features of the portable FX-901 soldering iron and demonstrate soldering an LED to a circuit board.
Thanks for watching!

The HAKKO HJ4000 SMD Rework Fixture is a cost effe...

The HAKKO HJ4000 SMD Rework Fixture is a cost effective solution for manual SMD rework using split-vision alignment precision, and can be used with select HAKKO hot air rework stations and IR preheaters for a complete, low-cost SMD rework system.

Thanks for watching!

In this video we showcase the CHP brand of electri...

In this video we showcase the CHP brand of electric torque screwdrivers, power supplies and numerous accessories.

The electric screwdrivers are designed for precision torque control and include a wide selection of brush, brushless and direct plug-in models with torque ranges from 0.26 - 21.7 lbf-in and speeds from 450 - 2000 RPM. All drivers are ESD safe to protect assemblies from electro-static shock. Watch to learn more.

Thanks for watching!

This video showcases an overview of some of the fe...

This video showcases an overview of some of the features and benefits of the HAKKO FX-951 soldering station, including the station parameters, the standard FM-2027 soldering iron and the FM-2032 micro soldering iron, T15 and T30 Series tips, and the station and iron holder sleep mode functionality.

Thanks for watching!

The FX-1002 micro soldering iron is used with the ...

The FX-1002 micro soldering iron is used with the HAKKO FX-100 RF Induction Heat Soldering System and is ideal for precision soldering of 0201 and other small SMD chip components, especially under microscopes and magnifiers.

Thanks for watching!

A look into the super high output power of the Hak...

A look into the super high output power of the Hakko HU-200.

The C5046 nozzle changer is a fast and easy way to...

The C5046 nozzle changer is a fast and easy way to remove and change desoldering nozzles on the FR-410 desoldering handpieces and the FR-301 desoldering gun. Use the C5045 for the FR-400 ultra heavy duty desoldering handpiece.

In this video we examine the unique features of th...

In this video we examine the unique features of the HAKKO HU-200 robotic soldering system.

This short 45 second video showcases some of the n...

This short 45 second video showcases some of the new enhanced features of the FT-802, which include an integrated handpiece holder on top of the station to maximize bench space, a hands-free blade removal plate, set screws to ensure blade alignment, an ergonomic heat resistant handpiece, and HAKKO G4 blades with superior thermal performance.

Thanks for watching!

A short 76 sec video showcasing some of the featur...

A short 76 sec video showcasing some of the features of the HU-200 robotic soldering system.

Learn how the HAKKO FU-500 solder feeder works whe...

Learn how the HAKKO FU-500 solder feeder works when combined with the HAKKO FX-601 soldering module and integrated with a robot for an automated robotic soldering system.

The CHP brand offers a vast selection of precision...

The CHP brand offers a vast selection of precision tools including, cutters, pliers, shears, wire strippers, lead formers, depaneling tools, and tweezers. The CHP cutters exhibit the same high quality performance of a forged tool but at a fraction of the cost.

The CHP high-quality ESD products will help preven...

The CHP high-quality ESD products will help prevent and protect against electrostatic discharge (ESD) that can occur on the workbench.

The CHP supplies include, grounding kits, wrist and heel straps, gloves, finger cots, static shield bags, tapes, labels and floor and bench mats, all at a reasonable price!

The CHP DFP 200 is a manual router table for depan...

The CHP DFP 200 is a manual router table for depaneling printed circuit boards from a panel or multi-block. The DPF 200 milling cutters (bits) cut the tab of the panel with the same quality as a expensive automated system but at a much lower cost. Features include, interchangeable guide rails designed for safety, an integrated vacuum system located directly on the guide rail to remove circuit board dust from the work area, ESD steel table construction with an Equipotential Bonding Point to protect against electro-static discharge, a wide selection of milling cutters (bits) with specific geometric shapes, locking casters for portablitly, and much more.

The C5027 board holder can be used independently o...

The C5027 board holder can be used independently or attached to the HAKKO C5028 or C5029 handpiece fixture for precise component rework. Features one-touch slide adjustment for fast and easy setup and fine X-axis adjustment.

The C5028 is a handpiece rework fixture for use wi...

The C5028 is a handpiece rework fixture for use with the HAKKO FR-810, FR-810B, and FR-811 hot air rework stations. This fixture is smaller than the large C5029 fixture and does not include the large metal platform plate or component tray.

The C5029 is a handpiece rework fixture with a lar...

The C5029 is a handpiece rework fixture with a large metal platform plate for use with the HAKKO FR-810, FR-810B and FR-811 hot air rework stations.

This bottom heater integrates solely with the HAKK...

This bottom heater integrates solely with the HAKKO FR-811 SMD hot air rework system.

A complete, economical SMD hot air rework system, ...

A complete, economical SMD hot air rework system, including the HAKKO FR-811 hot air station, bottom heater, board holder, handpiece rework fixture, and vision system.

An advanced SMD rework station with vacuum pickup ...

An advanced SMD rework station with vacuum pickup and a multitude of features for every need. When integrated with a bottom heater, board fixture and vision system, the FR-811 is a complete SMD rework system and the ideal choice for bottom terminated components.

The HAKKO FR-810B is ideal for removing SMDs and i...

The HAKKO FR-810B is ideal for removing SMDs and includes an integrated vacuum pickup system with a special visual indicator in the handpiece that allows the operator to visually see when the component has completely reflowed and is safely lifted from the pad.

The FR-410 is a 140-watt desoldering station with ...

The FR-410 is a 140-watt desoldering station with unique features that increases work efficiency, including newly designed selection of nozzles for a variety of desoldering applications.

The FR-810 SMD Hot Air Rework Station has a self-c...

The FR-810 SMD Hot Air Rework Station has a self-contained turbine air source and a powerful ceramic heater that delivers a hot air stream up to 1120В°F. This station is excellent for all SMD soldering and desoldering applications.

The FR-872 is a low profile, bench-top preheater d...

The FR-872 is a low profile, bench-top preheater designed to precondition circuit boards for soldering and desoldering more easily and with improved results.

Experience the power of the next generation of RF ...

Experience the power of the next generation of RF (induction heat) soldering with the Hakko FX-100 soldering system.

The FM-2032 micro soldering iron extends precision...

The FM-2032 micro soldering iron extends precision micro soldering capabilities to a variety of HAKKO soldering and rework systems.

The FX-888D is a low cost digital soldering statio...

The FX-888D is a low cost digital soldering station with user selectable preset temperature control, password protection, and low temp alarm.

After reflowing the soldered connection and the co...

After reflowing the soldered connection and the component has been removed from the PCB, residual solder remains in the through-holes. The 486 removes the solder with an air hood tool. Use the 486 with the Hakko 485 soldering system.

Watch the FT-8003 hot knife-blade slice through di...

Watch the FT-8003 hot knife-blade slice through difficult-to-cut wiring harness braid, including Nomex.

The FA-430 features two filters, comprising a thre...

The FA-430 features two filters, comprising a three stages filtering process, 3-airflow modes, and a filter change notification function. Compact and portable.

Watch the Hakko FM-206 Trailer...

Watch the Hakko FM-206 Trailer

Breathe easy with this compact, benchtop smoke and...

Breathe easy with this compact, benchtop smoke and fume absorber

A shop air desoldering and soldering station....

A shop air desoldering and soldering station.

A brief overview of the Hakko FR-801/802/803/803B ...

A brief overview of the Hakko FR-801/802/803/803B hot air rework stations

The FM-203 offers two soldering ports for a variet...

The FM-203 offers two soldering ports for a variety of tools that can be used in a variety of combinations, including soldering irons, SMD hot tweezers and/or desoldering tools

A dual purpose desoldering and soldeirng station w...

A dual purpose desoldering and soldeirng station with a built in vacuum pump.

Excellent for soldering and desoldering multi-lead...

Excellent for soldering and desoldering multi-leaded through-hole components and connectors mounted on printed circuit boards

An ideal tip maintenance system to help renew / re...

An ideal tip maintenance system to help renew / restore oxidized soldering iron tips and increase their longevity.

Free yourself from an electriical outlet with this...

Free yourself from an electriical outlet with this cordless soldering iron.

SMD hot tweezers with a revolutionary parallel act...

SMD hot tweezers with a revolutionary parallel action between the tip ends

An SMD mini hot tweezer for small chips as small a...

An SMD mini hot tweezer for small chips as small as 0201. Fits in the palm of your hand.

A quick guide on where to obtain the USB Driver so...

A quick guide on where to obtain the USB Driver software for the FR-811 and how to properly install it. The FR-811 is advanced SMD rework station with vacuum pickup and a multitude of features for every need. When integrated with a bottom heater, board fixture and vision system, the FR-811 is a complete SMD rework system and the ideal choice for bottom terminated components.

Learn step-by-step how easy it is to program the H...

Learn step-by-step how easy it is to program the HU-200 for point soldering with the pre-installed programming software.

Thanks for watching!

A brief guide into Hakko's HU-200 positioning syst...

A brief guide into Hakko's HU-200 positioning system.

A quick look into the built-in solder feeder for t...

A quick look into the built-in solder feeder for the Hakko HU-200 Robotic Soldering System.

A quick overview of the programming required for t...

A quick overview of the programming required for the Hakko HU-200 Robotic Soldering System.

In this video we test the resistance of an ESD mat...

In this video we test the resistance of an ESD mat per Standard ANSI/ESD S20.20 using a multi-meter versus two, five lb. electrodes and a resistance meter.

In this video we test the resistance of a Static S...

In this video we test the resistance of a Static Shield Bag per Standard Test Method ANSI/ESD S11.12 and S11.11 with a 5 lb. electrode and a resistance meter.

The FX-100 has a variety of features that can be a...

The FX-100 has a variety of features that can be accessed and set up with the display menu. Learn HOW TO engage "boost" mode, set up password lock out, auto power off and sleep function.

How To turn on and use the preset temperature mode...

How To turn on and use the preset temperature mode

How To "change" the preset temperatures that are u...

How To "change" the preset temperatures that are used in the preset mode

How To turn on and use the password lockout featur...

How To turn on and use the password lockout feature

How To program The FR-870 with a thermocouple usin...

How To program The FR-870 with a thermocouple using an auto profile

How To "program" the Hakko FR-803B with a thermoco...

How To "program" the Hakko FR-803B with a thermocouple

How To change the preset and working temperature...

How To change the preset and working temperature

How To setup the Hakko FM-2029 hot air pencil into...

How To setup the Hakko FM-2029 hot air pencil into an auto mode to follow a rework profile of heat, soak and reflow

How To turn off the grip alarm if not using all th...

How To turn off the grip alarm if not using all three handpieces at the same time

How To change the preset labels...

How To change the preset labels

How To change the parameters on the different chan...

How To change the parameters on the different channels

How To check if your FM-203 is ready for the Hakko...

How To check if your FM-203 is ready for the Hakko FM-2030 heavy duty soldering iron handpiece

A quick overview of the basic setup of the FM-206 ...

A quick overview of the basic setup of the FM-206 3-port rework system

Learn the basics of SMD soldering and desoldering...

Learn the basics of SMD soldering and desoldering

How To removed (desolder) large gold connector pin...

How To removed (desolder) large gold connector pins from a circuit board with the Hakko FM-2022 parallel remover (hot tweezers)

How To remove adhesive-bonded components with the ...

How To remove adhesive-bonded components with the Hakko FR-1418 BGA rework system

See the difference between tin-lead and lead-free ...

See the difference between tin-lead and lead-free solders

Watch and learn what customers have to say about t...

Watch and learn what customers have to say about the CHP DPF-200 manual router table.

Thanks for watching!

Learn how Hakko helped reduce LEDtronics' manufact...

Learn how Hakko helped reduce LEDtronics' manufacturing process cost by 50%

On this episode Kenta demonstrates the difference ...

On this episode Kenta demonstrates the difference between "changing" the soldering temperature and "adjusting" the soldering temperature on the FX-888D soldering station. He also showcases a brief overview of the optional accessories available for the station. This episode was broadcast and recorded LIVE on February 26, 2021.

On this episode we demonstrate the CHP brand DPF-3...

On this episode we demonstrate the CHP brand DPF-300 depaneling table. The DPF-300 is a manual router table for depaneling circuit boards (PCBs) from a panel or multi-block with the quality performance of an expensive automated system but at a much lower cost. The DPF-300 is equipped with an industrial-type electric motor spindle, eliminating the need for compressed air, and the steel guide rails are designed for safety and deliver a precision cut every time.
This episode was broadcast and recorded LIVE on September 11, 2020.
Thanks for watching!

When soldering or desoldering components on a circ...

When soldering or desoldering components on a circuit board, preheat is often needed to assist the work. In this episode we examine the HAKKO FR-830 and FR-870B preheaters and demonstrate how to replace the heater lamps on the FR-872 preheater.
This episode was broadcast and recorded live on August 13, 2020.
Thanks for watching!

On this episode we learn the basic operation of th...

On this episode we learn the basic operation of the FR-810B rework station, how to set and use the various system parameters and how to use it in manual mode and in semi-automatic mode by linking individual presets.
This production was broadcast and recorded LIVE on July 9, 2020.
Thank you for watching!

Learn how this dual port station can use 8 differe...

Learn how this dual port station can use 8 different handpieces and how to access and set all 10 parameter settings.
This production was broadcast LIVE and recorded on June 11, 2020.
Thanks for watching!

This episode focuses on how to use and set the six...

This episode focuses on how to use and set the six (6) parameter settings and a demonstration of some of the features of the HAKKO FX-951 soldering station.
This production was broadcast LIVE and recorded on May 21, 2020.
Thanks for watching!

Learn proper maintenance on the HAKKO FA-400 Smoke...

Learn proper maintenance on the HAKKO FA-400 Smoke Absorber and FA-430 Fume Extraction System in this episode of "Eye On Hakko."
This episode was broadcast LIVE and recorded on April 30, 2020.
Thanks for watching!

In this episode we demonstrate how to properly mai...

In this episode we demonstrate how to properly maintain your HAKKO desoldering tools, including the FR-301, FR-410's FR-4103 gun-type and FR-4104 pencil-type handpieces, the FM-2024, and the 817, which is used on the 472D desoldering station.
This episode was broadcast LIVE and recorded on April 23, 2020.
Thanks for watching!

Join us for a show and tell episode on the basic f...

Join us for a show and tell episode on the basic fundamentals of Soldering Iron Tip Maintenance with the HAKKO 599B tip cleaner, FT-700 tip polisher and FS-100 tip polishing paste.
This episode was broadcast LIVE and recorded on April 16, 2020.
Thanks for watching!

In this episode we demonstrate how to properly set...

In this episode we demonstrate how to properly set the temperature on the HAKKO FX-888D soldering station, and how to make a temperature adjustment using the Adjustment Mode, also known as calibration.

Thanks for watching!

In this episode of Eye On Hakko we preview some of...

In this episode of Eye On Hakko we preview some of the products we will be exhibiting at the IPC APEX 2020 exhibition in the San Diego Convention Center Feb. 4-6, 2020.

See us at Booth #1851.

San Diego Convention Center
February 4-6, 2020

Join us for an overview of the HAKKO FR-410 and FR...

Join us for an overview of the HAKKO FR-410 and FR-400 desoldering stations and the FR-301 portable desoldering hand tool.

This episode was broadcast LIVE and recorded on November 22, 2019.

Thanks for watching!

In this episode, the CHP Electric Torque Screwdriv...

In this episode, the CHP Electric Torque Screwdrivers, power supplies and accessories are showcased and demonstrated, including the announcement of American Hakko's CHP Electric Torque Screwdriver Trade-In program.

The CHP Electric Torque Screwdriver Trade-In program is a limited time offer from September 9 thru November 27, 2019.

This production was broadcast LIVE via GoToWebinar on September 27, 2019.

Thanks for watching!

Join us for an overview of the HAKKO FA-400 Smoke ...

Join us for an overview of the HAKKO FA-400 Smoke Absorber and the FA-430 Fume Extraction System.

This production was broadcast LIVE via GoToWebinar and recorded on August 30, 2019.

Thanks for watching!

Join us for an overview of the HAKKO FX-300 analog...

Join us for an overview of the HAKKO FX-300 analog and FX-301B digital solder pots, including a simple wire and component tinning demonstration.

This production was broadcast LIVE via GoToWebinar and recorded on June 28, 2019.

Thanks for watching!

In this episode we talk about some of the features...

In this episode we talk about some of the features of the HAKKO FX-100 RF Induction Heat Soldering System.
This production was broadcast LIVE via GoToWebinar and recorded on April 26, 2019.
Thanks for watching!

Join us for American Hakko's "Eye On Hakko" LIVE w...

Join us for American Hakko's "Eye On Hakko" LIVE web broadcast covering a general overview of HAKKO's soldering, desoldering, hot air rework, and fume extraction systems, and CHP brand hand tools, ESD supplies and electric torque screwdrivers.

This live production was broadcast via GoToWebinar and recorded on January 25, 2019

Thanks for watching!

Join us for an end of the year holiday special epi...

Join us for an end of the year holiday special episode featuring a brief preview of four new HAKKO products for 2019 that will be on exhibit at the IPC APEX EXPO Januray 29-31, 2019, at the San Diego Convention Center, San Diego, California.

This episode of "Eye On Hakko" was broadcast LIVE via GoToWebinar and recorded on December 20, 2018.

Thanks for watching.

Join us for American Hakko's "Eye On Hakko" LIVE w...

Join us for American Hakko's "Eye On Hakko" LIVE web broadcast featuring, the HAKKO Ultra Heavy Duty FX-801 Soldering station and the Ultra Heavy Duty FR-400 Desoldering station.

This production was broadcast LIVE via GoToWebinar and recorded on November 15, 2018.

Thanks for watching.

This video demonstrates how to use some of the fea...

This video demonstrates how to use some of the features of the FX-100 soldering system (Sleep Mode, Auto Shut-OFF, etc.) including a short tutorial on proper tip maintenance and the introduction of the HAKKO FX-1002 micro soldering iron.